How to PROPERLY Repair a Rust Hole in your Car or Truck (DIY for Beginners)

29 Bal 2020
3 958 267 Peržiūros

Rust hole removal and repair. Repairing a rust hole in your car is something that should be done quickly to prevent it from spreading. You can easily do this at home with some practice and get the results you see in this video. I teach you the basics of what welder you want to use and how to weld so you can get started. I answer questions like, should you butt weld or lap weld floor panels? Rust is common at the wheel wells, quarter panels, rocker panels, and floor boards of cars and in this video I show the proper and most thorough way to remove and repair rust.
Buying this car for $300: ltworlds.info/home/vaizdo-ra-as/nIiKk5xids1pY6g.html
Rust Repair WITHOUT a Welder: ltworlds.info/home/vaizdo-ra-as/02ao2NaLYpGlm7Q.html
PRODUCTS:
Cheap Flux Core Welder: amzn.to/2SjkaHa
Cheap MIG Gas Welder: amzn.to/2Yg8Hfn
Welder I Used: bit.ly/WelderMIG
Vent Tubing: amzn.to/3d3RQ3z
Blower Fan:amzn.to/35lj3MH
Full Face Respirator w/ Filters: amzn.to/2W520tU
TURBO KIT: bit.ly/TurboKit
Rust Paint: amzn.to/3d4BRT3
Sheet Metal Nibbler: amzn.to/3bO0YsX
Angle Grinder: amzn.to/2W6St5K
Wire Wheel: amzn.to/2WdalvP
Digital Caliper: amzn.to/3bPzxiv
Socket Set: amzn.to/3cZkLG1

→ As an Amazon Associate I earn from qualifying purchases.
→ Become a ChrisFix Subscriber: ltworlds.info
→ Instagram: instagram.com/chrisfixit
→ Facebook: facebook.com/chrisfix8
→ Website: www.ChrisFixed.com
→ My Channel Home Page: ltworlds.info
**If the video was helpful, remember to give it a "thumbs up" and consider subscribing.**
Disclaimer:
Due to factors beyond the control of ChrisFix, I cannot guarantee against improper use or unauthorized modifications of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ChrisFix recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ChrisFix.

Komentarai
  • A job weld-done

    GODAssasinGODAssasinPrieš val
  • i didnt think kobber wouldnt get welded, thx a lot now i can fix the rusthole in the side of my tracktor a lot easier, its an old IH 434 :D

    Max bennedbækMax bennedbækPrieš 11 val
    • Awesome! Let me know how it goes!

      ChrisFixChrisFixPrieš 2 val
  • Where is video about turbo?

    Misho vlogsMisho vlogsPrieš 17 val
  • Should always grind your welds flush and seam seal the welds then hammerite

    Knockout PowerKnockout PowerPrieš 21 val
  • The rust hole looks like Afrika

    drapstydrapstyPrieš dieną
  • African rust

    Salami LidSalami LidPrieš dieną
  • Good work! Love this video. Thanks

    Peter ClarkPeter ClarkPrieš dieną
  • I wish there was a video for how to fix a 76 Cadillac trunk motor. Mine is shot

    Shawn Gaming HDShawn Gaming HDPrieš dieną
  • I can't wait for the turbo install!!!

    ĐëvøňĐëvøňPrieš dieną
  • Hi Chris fix, where you located, please. Am in Daytona Beach..

    Junior WearJunior WearPrieš dieną
  • yo he sounds like bushy brows from naruto 14:24

    Dylan BinghamDylan BinghamPrieš dieną
  • Very interesting for a beginner like me ,much appreciated ,thanks

    Herun PersunHerun PersunPrieš 2 dienas
  • That rust hole looks like africa lol

    yavuzzzyavuzzzPrieš 2 dienas
  • where is the video of instaling a turbo p.s luv u chirs

    Plamen PaciPlamen PaciPrieš 2 dienas
    • Stay tuned!

      ChrisFixChrisFixPrieš 2 dienas
  • No grind and bondo lol 😂

    ess210sess210sPrieš 2 dienas
  • love ur vids but a welder sir u are not

    MR tMR tPrieš 2 dienas
  • Is it just me or does the hole look like afrika?

    LulasLulasPrieš 2 dienas
  • How the F is this a beginners DIY

    DrtomaderoDrtomaderoPrieš 2 dienas
  • I don't even have a car. Just like to watch things get fixed.

    TednTinTednTinPrieš 3 dienas
  • Any defender owners here?

    Matthew AllcockMatthew AllcockPrieš 3 dienas
  • how called this black things under the back tyres to lift vechicle up for bottom repair? looks like this things absolutelly absent in my country russian shops

    andrew RLandrew RLPrieš 3 dienas
  • wonderfull video, professional and safe methots are being used.

    Halil AvcılarHalil AvcılarPrieš 3 dienas
  • Why are you not making videos of the del sol anymore?

    ceeb2 thojceeb2 thojPrieš 3 dienas
  • before this video if my car looked like that: idk what to do to fix this it will take 100 men or more

    Yuri GagarinYuri GagarinPrieš 3 dienas
  • That hole of rust looks like africa

    2005_ford_crown_victoria_p712005_ford_crown_victoria_p71Prieš 3 dienas
  • Bloody heck Good job on that

    PichaelmalmerPichaelmalmerPrieš 3 dienas
  • 👍

    Ahmed SamyAhmed SamyPrieš 3 dienas
  • Is nobody gonna talk about how the rust hole looks a lot like Africa

    Yaboi LemonboiYaboi LemonboiPrieš 4 dienas
    • I was literally about the write the same comment. Dude...haha

      Common Man CryptoCommon Man CryptoPrieš 20 val
  • 19:00 Have you ever thought about turning the roll around so that it comes off better?

    Lachshot BossLachshot BossPrieš 4 dienas
    • @Allen Williams oh true

      Lachshot BossLachshot BossPrieš 2 dienas
    • The diagram inside the cover shows the proper way to load the wire. It will work much better if loaded that way

      Allen WilliamsAllen WilliamsPrieš 2 dienas
  • I watched this whole video and I don’t even have a car but it’s so entertaining

    OrieOriePrieš 4 dienas
    • Yup Same It's just so calming and rewarding? In a way?

      GODAssasinGODAssasinPrieš val
  • Chris fix gets new car hey guys chris fix here today I got a new car and I'm making a drag car and I'll be doing it a my home in my drive way with common hand tools and of course we have bolts and we will need medium strength thread locker

    Nascar lover 13Nascar lover 13Prieš 4 dienas
  • No wonder this channel has so many subs.

    Great BreadGreat BreadPrieš 4 dienas
  • Was ist das denn für ein Pfusch? Nicht mal den Rost ganz weg geschnitten!!!!!!!!!!!!

    Fritz PumpelmusFritz PumpelmusPrieš 5 dienų
    • Did you watch the video?

      ChrisFixChrisFixPrieš 4 dienas
  • is it the same process to fix a hole in a fender/doorframe? i have a 2006 ford crown victoria with a major rust hole on the rear quarter and rear fender.

    Clayton SClayton SPrieš 5 dienų
  • This guy is awesome! He's looking up a great future and big opportunities.

    Laszlo TothLaszlo TothPrieš 5 dienų
  • I'm in Canada, more rust and far more regulation! You touched on mig welding, but locally the gas tubes (cylinder/tank) are $600 to $1500 (80cf to 300cf) (first fill incl.) and contracts begin at $300 to $500 per year purchased tank or $400 to $700 with rental of tank. Also here if a buy a CO² tube, you can't do mixes as each mix is a dedicated tube colour by law. If that was not enough suppliers will not fill anyother companys tubes. Can I bypass this and if so how? The federal regulations say UN and DOT approved tubes will be willingly filled by every licenced supplyer yet the federal legislation is not enforced and seamingly has no teeth! All currency is in Canadian dollars!

    Misha LeBlancMisha LeBlancPrieš 5 dienų
  • The rust hole looks like Africa 😂😂😂😂

    Bruce BeeBruce BeePrieš 5 dienų
  • Thanks a lot💪

    Adrian PopAdrian PopPrieš 5 dienų
  • ваще не красиво заварил

    Раил БакировРаил БакировPrieš 6 dienų
  • Dude your videos are just amazing, I have an old vw bus and look at the rust every time I drive it. It’s videos like this that get me excited and show me just what’s out there for things to do. Great channel, thanks Chris :)

    Gabriel MartinoGabriel MartinoPrieš 6 dienų
    • I'm glad the video gets you excited and shows you how to fix the rust! Thanks a lot!

      ChrisFixChrisFixPrieš 6 dienų
  • You didnt show the bottom part...😷🥰

    Marc JuniorMarc JuniorPrieš 6 dienų
    • @ChrisFix Good job Chris...I am not interested in your welding tools and sheet metal cutting tools. That is awsome...👍👍👍🇵🇭

      Marc JuniorMarc JuniorPrieš 5 dienų
    • Weld the top, paint the bottom and you're good to go!

      ChrisFixChrisFixPrieš 6 dienų
  • Why not just sand it and put clay epoxy?

    God OfWine&TitsGod OfWine&TitsPrieš 6 dienų
  • Awesome Info

    Javier CastilloJavier CastilloPrieš 6 dienų
  • Where are other episodes of this series Chrisss?

    Berk KoşanerBerk KoşanerPrieš 6 dienų
  • Nobody in the comments mention How the "thumnail looks like Africa" the rusty hole.

    MINDLESS EMPIREMINDLESS EMPIREPrieš 7 dienų
    • @I Smoke Two Joints Before I Smoke Two Joints 😅

      MINDLESS EMPIREMINDLESS EMPIREPrieš 4 dienas
    • You beat me to it lol

      I Smoke Two Joints Before I Smoke Two JointsI Smoke Two Joints Before I Smoke Two JointsPrieš 5 dienų
  • Can’t wait to see you put a turbo in the del sol!

    Ambush362Ambush362Prieš 7 dienų
  • It appears you have your mig wire roll upside down. Should be feeding from the bottom.

    CutletsCutletsPrieš 7 dienų
  • If you get a big gap just bead weld over it

    Steven WilsonSteven WilsonPrieš 7 dienų
    • No

      Yee YeeYee YeePrieš 5 dienų
  • Who does the rust in the the tumbnail look like africa

    Bento BekkerBento BekkerPrieš 7 dienų
  • ckris you are wander full man but you don,t know how for welding

    nasser ghaffarinasser ghaffariPrieš 8 dienų
  • Bro, you must have a golden heart cause people are bad these days, they won't share this kind of information, but you do. Thank you !!!

    Xloyan VXloyan VPrieš 8 dienų
    • I appreciate that!

      ChrisFixChrisFixPrieš 8 dienų
  • Did y’all see his kill switch 😂😂

    Futuristic Designs Custom built PC'sFuturistic Designs Custom built PC'sPrieš 8 dienų
    • That's for the odor remover: ltworlds.info/home/vaizdo-ra-as/z5mDptV1qq92lNI.html

      ChrisFixChrisFixPrieš 8 dienų
  • Phil Swift here with Flex Tape!

    Not_RealNot_RealPrieš 8 dienų
  • Would love to see a video of doing this to an exterior body panel like a fender. Awesome vid as always and looking forward to the turbo del sol!

    Mathieu SirjooMathieu SirjooPrieš 8 dienų
  • Great video as always. Maybe just put in an annotation for a quick epilepsy warning from 24:55

    Cornflakes YognautCornflakes YognautPrieš 9 dienų
  • Hello very useful video, than you so much, i have a mustang 2003 withe exactly the same problem, I'm looking for a floor pan but I haven't been lucky, if someone knows where can I get the driver side please let me know, that would be very grateful, thank you

    Nelson AlvaradoNelson AlvaradoPrieš 9 dienų
  • Fantastic video. Thank you. I'm interested to get an old Porsche 912, but the ones I can afford have a lot of floor pan and other areas of rust. Now I feel I can do it myself at home, affordably and with confidence, after watching your video.

    From The Peanut GalleryFrom The Peanut GalleryPrieš 9 dienų
  • Çok konuşuyor

    Furkan ŞimşekFurkan ŞimşekPrieš 9 dienų
    • Thanks for sharing

      ChrisFixChrisFixPrieš 9 dienų
  • 31:24 use phosphoric acid to etch hard bad red rust to black which is inactive and also acts as a rust inhibition in the long run. Then top coat with regular procedure.

    Ashok RevannaAshok RevannaPrieš 9 dienų
    • I'll have to check that out, thanks for sharing!

      ChrisFixChrisFixPrieš 9 dienų
  • Learnt more useful tips on welding from a car detailer than any of the other welding channels.. ChrisFix 💪🏼💪🏼💪🏼 no wonder I subscribed ages ago!

    Raico RosenbergRaico RosenbergPrieš 9 dienų
    • Thanks a lot Raico!

      ChrisFixChrisFixPrieš 8 dienų
  • great workmanship chris, i have to do similar to my landcruiser and you have helped me a lot .cheers from ireland

    Jimmy O TooleJimmy O ToolePrieš 9 dienų
    • Glad I could help! Thanks for the support from Ireland!

      ChrisFixChrisFixPrieš 8 dienų
  • As a welder and a fabricator, you don't need to de oil or de grease the area, oil act as an anti spatter which gives you a cleaner surface so you don't need to grind much

    Luke PhillipsLuke PhillipsPrieš 10 dienų
  • Getting tired talktalktalk, Jezus christ take a pill

    Peter vPeter vPrieš 10 dienų
  • What a teacher! Have watched several of your videos and am impressed not just by your knowledge, but by how you are able to convey useful info. Really good job, you have a gift for instructional videos.

    Rick KoehlerRick KoehlerPrieš 10 dienų
  • Thank you very much, that was one of the most helpful informative videos ive ever watched, BRILLIANT !!!

    Micky HarkinMicky HarkinPrieš 10 dienų
  • good job, greetings from germany

    Peter WeberPeter WeberPrieš 10 dienų
  • Great channel my friend

    thebigseahorsethebigseahorsePrieš 11 dienų
  • 18:56 the wire roll is upside down?

    Johann JakobJohann JakobPrieš 11 dienų
  • Where is the turbo kit video at 😭😂😂

    Andres BugarinAndres BugarinPrieš 11 dienų
  • This guy is awesome

    Sukma Adhi WijayaSukma Adhi WijayaPrieš 11 dienų
  • Your rust hole looks like Africa

    Brian BrownBrian BrownPrieš 11 dienų
  • Fantastic guide Chris. Well planned and edited to keep engaged throughout. So many tips I wasn’t expecting too. Thanks from a bloke in the uk trying to keep his rusty VW on the road..

    Graham KnottGraham KnottPrieš 11 dienų
  • I live down the street from Chris' house and think his family are cool people. Hi to Coach!

    VideoNOLAVideoNOLAPrieš 11 dienų
    • @David Martínez You can just Google that (chrisfix ericthecarguy) and something should come up; they are in a video together. And elsewhere online, too.

      VideoNOLAVideoNOLAPrieš 9 dienų
    • @videoNOLA face reveal?

      David MartínezDavid MartínezPrieš 9 dienų
  • When is your next Del Sol video coming out? I am excited to watch the rest of the changes and modifications.

    Taylor HartTaylor HartPrieš 12 dienų
  • I cant comment in here, why? My 55 y/o car is sick with rust.

    Mick CarsonMick CarsonPrieš 12 dienų
  • Excellent video.

    Johnny RodriguezJohnny RodriguezPrieš 12 dienų
  • Well we used to have a old russian truck, and it had a small rust hole. So if i was in the passenger seat i would see that rust hole every time. (also without a carpet or mat.)

    LukasPlayzLukasPlayzPrieš 12 dienų
    • It's a ZIL 130.

      LukasPlayzLukasPlayzPrieš 12 dienų
    • Thanks for sharing! What kind of truck was it?

      ChrisFixChrisFixPrieš 12 dienų
  • The finish doesn't look good and smooth.. But it doesn't matter since it will be covered with some mating or carpet.. what's important is there's no gap where water can shoot up, and the weld can hold good amount of weight without developing any cracks..

    Paul Raymund ChanPaul Raymund ChanPrieš 12 dienų
    • Exactly!

      ChrisFixChrisFixPrieš 12 dienų
  • The finish doesn't look good and smooth.. But it doesn't matter since it will be covered with some mating or carpet.. what's important is there's no gap where water can shoot up, and the weld can hold good amount of weight without developing any cracks..

    Paul Raymund ChanPaul Raymund ChanPrieš 12 dienų
  • 5:22 is it just me or does that rust hole kinda looks like Africa?

    SimpleManMikeSimpleManMikePrieš 12 dienų
    • @Its a Long Story me too

      shadow6687shadow6687Prieš 5 val
    • @jblo nah it looks like Africa

      Salami LidSalami LidPrieš dieną
    • @pöhnö shit that was good lol

      SimpleManMikeSimpleManMikePrieš 2 dienas
    • Yeah it has no water

      pöhnöpöhnöPrieš 2 dienas
    • I was thinking the same

      Ambush362Ambush362Prieš 7 dienų
  • Excellent example of repairing sheet metal by welding but if you want to make the job more easier and just as strong why not braze using 5631 silver alloy and never have to worry about corrosion at the seam for a much longer lasting repair?

    David HeinsDavid HeinsPrieš 12 dienų
    • I'll have to check that out, thanks for sharing!

      ChrisFixChrisFixPrieš 12 dienų
  • Hey Chris, my son and I have been watching you rebuild this Honda. Please let me know if you want to sell it later. We are loving what your doing with the car

    ZapTanner 2005ZapTanner 2005Prieš 12 dienų
  • I’ve put on the face mask, instructions unclear though. Making meth now.

    Jerome ClaessenJerome ClaessenPrieš 12 dienų
  • Still waiting for the turbo 😐

    Fr0sty GamingFr0sty GamingPrieš 13 dienų
  • I found even a faster way to fix that rust hole in ones' car, no matter where it is... I call it; The under five fix...(under $5.00 and under 5 minutes of your time!) Introducing.... The single can of spray foam! Just spray it in, let dry and paint 🎨 to your hearts content!! Voila!! You're done!! Now go trade in your vehicle and carry on!!

    Will ParsonsWill ParsonsPrieš 13 dienų
    • Thanks for sharing

      ChrisFixChrisFixPrieš 13 dienų
  • I think it would be a cool idea if you did a video on how to paint your car at home.

    Ryan CatapanoRyan CatapanoPrieš 13 dienų
  • The hole on the thumbnail looks like Africa.

    lulu22lulu22Prieš 13 dienų
  • I store my paint cans upside down. Never had dried up or hardened paint. This lasts for years.

    Johan LastJohan LastPrieš 14 dienų
  • Tanta herramienta para el trabajito que es

    noeli150471noeli150471Prieš 14 dienų
    • That's what you need in order to properly weld in the sheet metal!

      ChrisFixChrisFixPrieš 14 dienų
  • This job we need to remove our fuel tank or not?

    Haziq HadiHaziq HadiPrieš 14 dienų
    • Depends on how close you are working to the fuel tank!

      ChrisFixChrisFixPrieš 14 dienų
  • What's the cost for a job like this???

    Daidai GoreDaidai GorePrieš 15 dienų
  • The two dresser quantitatively attach because napkin latterly touch plus a truculent sister-in-law. cooing, breakable tempo

    Kristy WellsKristy WellsPrieš 15 dienų
  • Hey Chris, anyway we can get the turbo video for this car? No rush! Just curious

    LiynoxLiynoxPrieš 15 dienų
  • Excellent video, good information on how-to with demonstration, I Like and Subscribed. 👍👍👍👍👍

    raptors316raptors316Prieš 15 dienų
  • Looks like someone pissed the seat.

    T̲e̲x̲t̲ ̲T̲R̲A̲M̲P̲ ̲t̲o̲ ̲8̲8̲0̲2̲2̲T̲e̲x̲t̲ ̲T̲R̲A̲M̲P̲ ̲t̲o̲ ̲8̲8̲0̲2̲2̲Prieš 15 dienų
  • The hole from the inside looks like africa

    Trax BondTrax BondPrieš 16 dienų
  • Finally about Welding. I already knew how to weld been waiting forever so I decided just to weld after watching other welding videos.

    StripeCatFlipStripeCatFlipPrieš 16 dienų
    • @ChrisFix do the Fluxes welding. I promise I wont scape ads.😂😂😂

      StripeCatFlipStripeCatFlipPrieš 16 dienų
    • Awesome!

      ChrisFixChrisFixPrieš 16 dienų
  • I love how you explain everything I’m doing most my work now so thank you so much

    Corporate Security Intelligence Services LLC CSISCorporate Security Intelligence Services LLC CSISPrieš 16 dienų
    • That's what I love to hear! Thanks a lot!

      ChrisFixChrisFixPrieš 15 dienų
  • Put all of the parts in the mustang

    Game and the prank Channel cGame and the prank Channel cPrieš 16 dienų
  • The turbo no put in the mustang

    Game and the prank Channel cGame and the prank Channel cPrieš 16 dienų
    • @ChrisFix are you going to build the engine for that?

      SabaSabaPrieš 2 dienas
    • The DriftStang is getting the supercharger!

      ChrisFixChrisFixPrieš 15 dienų
LTworlds